3/24/2023 0 Comments Key tubbler 1986 ford f150![]() Remove the drive gear, snapring and washer from the cover casting along with the upper actuator.Ĭlean all components and replace any that appear damaged or worn. The removal of the casting cover will expose the upper actuator. Remove the 4 attaching screws from the cover casting and lift the casting over the end of the steering shaft, allowing the turn signal switch to pass through the casting. Remove the turn signal switch up and over the end of the column, but don't disconnect the wiring. Remove the turn signal switch attaching screws. Remove the lock cylinder and the drill shavings. (44mm), until the lock cylinder breaks loose from the steering column cover casting. drill bit, drill down the center of the ignition lock cylinder key slot about 1 3/ 4 in. Place a chisel at the base of the ignition lock cylinder cap and using a hammer break away the cap from the lock cylinder. ![]() Tilt the column to the full down position. drill bit, mounted in a right angle drive drill adapter, drill out the retaining pin, going no deeper than 1/ 2 in. Tilt the steering column to the full up position and prepunch the lock cylinder retaining pin with a sharp punch. The lock cylinder retaining pin is located on the outside of the steering column cover casting adjacent to the hazard flasher button. Pull out the hazard switch and tape it in a downward position. Cover the seat and floor area with a drop-cloth. Cover the entire circumference of the casting. Using masking tape, tape the gap between the steering wheel hub and the cover casting. Check that the vehicle starts only in PARK and NEUTRAL. It is best to install a new upper bearing. Upon reassembly, the following parts must be replaced with new parts:Īssembly is a reversal of the disassembly procedure. Remove the lock actuator insert, the T-bolts and the automatic transmission indicator insert, or, with manual transmissions, the key release lever. Remove the flange casting, upper shaft bearing, lock cylinder, ignition switch actuator and the actuator rod by pulling the entire assembly over the end of the steering column shaft. Remove the snapring and T-bolt nuts that retain the flange casting to the column outer tube. Remove the ignition switch and warning buzzer and pin the switch in the LOCK position. Unbolt the steering column and lower it carefully. Non-Functioning Cylinder or No Key Available The remainder of installation is the reverse of removal. This will allow the cylinder retaining pin to extend into the cylinder cast housing hole. Assure that the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. When installing the cylinder, turn the lock cylinder to the RUN position and depress the retaining pin, then insert the lock cylinder into its housing in the flange casting. wire pin in the hole in the casting surrounding the lock cylinder and depress the retaining pin while pulling out on the cylinder. Place the shift lever in PARK and turn the key to ON. Unplug the wire connector at the key warning switch. On tilt columns, remove the upper extension shroud by unsnapping the shroud from the retaining clip at the 9 o'clock position. Thank you.For trucks with dash mounted switches, see Chassis Electrical. The ignition lock cylinder activates the ignition switch to. This is just so that your expert is credited for their time and services. The ignition lock cylinder on your Ford F-Series is the tumbler and key used to start your truck. Please note that if you have a subscription service, you still are required to rate service, however you are not charged again. Please remember to rate service using the rating page so that I may receive credit. ![]() Just bookmark this page so you can access my profile easy and post a new question from the question box on my profile page. If you have new questions now or in the future please do not hesitate to ask them. ~Do you still need more help? ~Confused by my info request or answer? ~Need more time? ~Confused on how the site works? ~Need more detail or a different explanation? If the answer is YES to any of these just press reply and lets work on this concern some more. I would sure appreciate it if you would reply so I can offer my skills and knowledge and repair guide access to help as best I can. I noticed we have not yet resolved your concern you asked about.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |